SJ-Swaco MD-2/3 shaker screen is a kind of composite frame shaker screen specified for both M-I SWACO MD-2 dual flat-deck shaker and MD-3 triple-decker shale shaker. M-I SWACO MD-2 shale shaker is suitable for both onshore and offshore applications and MD-3 triple-decker shale shaker mainly targets primarily high-end offshore operations. Reinforced PT frame reduces the friction between the screen and deck plate. Featured by higher throughput, extended screen life, fewer replacements, our screens aim to lower the cost of mud treatment.
Technical Parameter
Adaptable Shale Shaker Model
SJ-Swaco MD-2/3 shaker screens are used as the substitute screen for
Remarks:
M-I SWACO, MD-2, MD-3 are marks of M-I L.L.C.
ShengJia only produces the replacement screens but not original from M-I SWACO
Swaco Md-2 Shaker Screen,Swaco Md-2 Shale Shaker Screen,Shaker Screen,Swaco Shakers Anping Shengjia Hardware Mesh Co.,ltd , https://www.oilshakerscreen.com
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131"; Home>Bearing knowledge>koyo bearing work hot cause and noise treatment Koyo bearing work hot cause and noise treatment
A: koyo bearing work in the cause of hot: /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
1. It depends on the temperature at which the bearing arrives; whether it can be within the scope of the agreement; whether the koyo bearing selection is correct; whether it can exceed the koyo bearing depiction function.
2. Check whether the accuracy of koyo bearing can meet the requirements; whether it can be damaged. The influence of the environment on the NTN bearing; whether the particulate matter such as dust can enter the koyo bearing
3. Note that the pre-tightening force of the koyo bearing should be even when the device is installed; do not pre-tighten too much; the clearance becomes smaller
4. Extremely capable of smooth oil or grease selection is unreasonable; smooth system configuration can be reasonable; heat dissipation is not good 2: koyo bearing noise treatment program:
The koyo bearing sounds because the rolling body rolls over the raceway surface; this is the basic feature of all bearings. The spherical bearings are different; the spherical bearing's rolling momentum is irregular; its main frequency does not follow The speed is changed; however, the total sound pressure level is added with the acceleration of the rotational speed. The bearing with large rolling sound; the sound pressure level of the raceway sound is reduced with the addition of viscosity, and the bearing with small rolling sound; its sound pressure When the viscosity increases to about 20mm2 / s or more; from the reduction to the increase. The rigidity of the bearing seat is greater; the total sound pressure level of the raceway sound is lower. For example, the radial clearance is too.淖苌辜 淖苌辜 é«Œ é«Œ é«Œ å´´å€å•ª å´´å€å•ª å´´å€å•ª å´´å€å•ª è›´ ç¼é»¾ ç¼é»¾ ç¼é»¾ ç¼é»¾ ç¼é»¾ ç¼é»¾ ç¼é»¾ ç¼é»¾ ç¼é»¾ ç¼é»¾ æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控 æ“控. Sound often affects the noise of the entire machine; reducing the sound of the raceway can reduce the noise of the entire machine.
Secondly; the impact sound of the rolling body and its control method. The larger type of ball bearing or cylindrical roller bearing works under low speed under pure radial load; because the centrifugal force of the rolling body is awkward than the τ 汕 汕 汕 汕 汕鞅3 芑蚬龅 Indigo 3. 鲈肷. But as the speed of rotation progresses; this movement will disappear. The control methods for the roll impact sound are: properly reduce the radial clearance; use reasonable layout and the information is harmonious. Spherical cage bearing.
Finally, the rolling noise of the bearing and its control method are the sharp metal conflict sounds of cylindrical roller bearings that can occur in all occasions; most of them occur in the larger type of grease-smooth bearing; Smooth fat is more likely to attack; it does not occur when the oil is smooth. In addition; it is easier to attack in winter; when it receives pure radial load; it is easy to attack when the radial clearance is large; and it is different depending on the size of the type. It is easy to attack in a certain range of speed; it will be intermittent and intermittent. The special processing method of the outer ring raceway can avoid the appearance of rolling sound; if necessary, the bearing can be used; or the bearing can be properly cut Radial clearance; the use of excellent smooth grease and improved rigidity with bearing-like parts.
Recommend to friends comments close window Bearing related knowledge Analysis of the development status of new product fan bearing skills required for oil-free bearing-mold occupation
Removal, Inspection and Repair of KOYO Bearings and Analysis of Linear Bearing Series Analysis of Cylindrical Roller Bearings
This article links to http://
Please indicate China Bearing Network http://
Previous:Selection of clutch bearing Next: Analysis: Functional requirements of motor bearing grease
Swaco Md-2 Shaker Screen/MD-3 Shaker Screen
Replacement Screens for M-I SWACO MD-2 & MD-3 Shakers
Competitive Advantage
Source: Bearing network time: 2014-06-20