The corundum flooring material consists of special wear-resistant aggregates with high-quality cement, special additives, etc. Premix production, strict ratio control, stable quality, and direct application at the construction site. The "AOT" emery surface is dry-sprayed and solidified with the concrete base layer, forming a dense, hard, highly wear-resistant and dust-resistant surface layer on the ground. Emery flooring materials are a building material that non-professionals may find strange. I will introduce it in a simple and easy-to-understand way to help you further understand the silicon flooring material . What is Emery flooring material Emery flooring materials are mainly composed of cement, wear-resistant aggregates, additives, and other substances, and have high requirements for these substances. Several kinds of raw materials are strictly proportioned and produced through premixing so as to ensure the stability of the quality of the silicon carbide flooring. It can be used directly during the construction process. Emery Floor Material Uses As a building-protecting material for the ground, carborundum floor materials are mainly used in parking lots, warehouses, factories and other places, with particular emphasis on areas where traffic is frequent. Emery flooring material advantages 1. The cured surface has high hardness and wear resistance. 2. Make the ground withstand people's impact load. 3, with the overall integration of grass-roots concrete, can not afford to drum, do not fall off. 4. The hard and compact surface can resist the penetration of grease, special hydraulic oil, and various industrial chemicals. 5, easy and simple daily cleaning, save materials, reduce costs. 6, can meet the requirements from smooth to non-slip. 7, pre-packaged products, on-site construction without the need to add other materials. 8, a variety of colors to choose from, help improve the working environment. 9, shorten the construction period and save time. 10. Economicality: 1) Do not need to perform other surface treatment and daily maintenance to prolong the service life of the ground and reduce the maintenance cost; 2) Avoiding the cost of periodic coating and ground thickening of the coating surface; 3) It avoids the disadvantages of ordinary concrete ground, terrazzo floor, and tile floor breaking the access of workplaces due to damage repair, thereby greatly improving the effective utilization rate of the workplace and optimizing the economy. Therefore, from an economic point of view, the "AOT" brand floor material is most suitable for the construction of modern factories, warehouses, parking lots, and warehouse supermarkets. Emery floor material construction introduction First, the basic concrete requirements 1. The concrete strength of the grass-roots level should be above C25, the water-cement ratio should be controlled below 0.50, the concrete slump should be controlled within 75-100mm, and the concrete mixture should be kept to a minimum and the bleeding should be controlled. 2. In order to ensure that the concrete mixture has sufficient fluidity and conducive to construction, it is recommended that concrete be added with an appropriate retarder. 3, pay attention to the corner of the concrete construction block, take extra strengthening treatment. Second, plan coverage 1. Divide the ground into a certain area. 2. Prepare enough materials for two-stage construction. Third, the first phase of construction Note: high temperature or windy weather will accelerate the curing of concrete, reducing the allowable construction time 1. When the concrete is solidified (a slight 3mm footprint is left in the pedestrian traffic) 2. Excess surface bleeding needs evaporation or suction. 3, uniform tear cloth about 1/2 ~ 2/3 of the material on the concrete surface. Fourth, smooth 1. The surface of the material to be torn for the first time is darkened, indicating that sufficient water has been absorbed from the concrete on the surface. 2. Use a wooden wipe or a polishing machine with a disc to smooth it out. 3, to ensure that all corners are fully compacted. V. Second stage construction 1. Evenly tear the floor hardener in the direction perpendicular to the first. 2, using electric steel spatula or disc polishing machine. Six, received light 1. When the surface of the concrete is hard enough not to be damaged, use a polishing machine with a slightly inclined blade to smooth and close the light. 2. Use water or special curing agent for curing. Editor's summary: The above is the introduction of the use of corundum floor materials and construction. When selecting this kind of material, we must pay attention to the content of emery aggregate, which is a key factor affecting the quality of the floor. In addition, we must choose regular manufacturers, try to bypass the middlemen to choose independent manufacturers, many middlemen in order to seek benefits often shoddy, harming the interests of consumers. Floor Decoration Materials Brand Decoration Materials List Decoration Materials Knowledge Hydroelectric Material Brand Pp Sink,Lab Pp Big Sink White,Pp Small Sink Grey,Polypropylene Lab Sink NARWILL IMPORT&EXPORT CO.LTD , https://www.narwill.com
