1. Heating should be gradual in the first use; When using geothermal floor, consumers must pay attention to the floor and floor heating step by step. When installing, the surface temperature should be kept at around 18 °C. Before installation, the cement floor should be gradually heated up, increasing by 5 °C every day until it reaches the standard of about 18 °C. In the first 3 days after the installation is completed, this temperature should be maintained. After 3 days, the temperature can be raised as needed, and the temperature can only be raised by 5 °C per day. The first time you use geothermal heating, be careful to heat up slowly. When used for the first time, the first three days of heating should be gradually warmed up: the first day water temperature 18 ° C, the next day 25 ° C, the third day 30 ° C, the fourth day can be raised to normal temperature, that is, water temperature 45 ° C, surface temperature 28 °C ~ 30 °C. Can not heat up too fast, too fast, the floor may be cracked and twisted due to expansion. When the geothermal heating system is activated again after a long time, it should be heated as strictly as the first time. 2, the surface temperature can not be too high; It should be noted that with geothermal heating, the surface temperature should not exceed 28 ° C, and the water pipe temperature should not exceed 45 ° C. If this temperature is exceeded, it will affect the service life and service life of the floor. The average family, when the room temperature reaches 22 °C in winter, is already very comfortable. If the temperature rises normally, it will not affect the use of geothermal floor. 3, close the geothermal system, pay attention to the gradual cooling; As the seasons go through, when the weather is warm and the indoor heating system is no longer needed, it should be noted that there is also a process to shut down the geothermal system. The cooling process of the floor should be gradual and not dip. If the cooling rate is too fast, It also affects the life of the floor. 4, when the room is too dry, you can consider humidification; The dry climate in winter, coupled with the use of geothermal heating, the floor is prone to cracking when it is exposed to high temperatures for a long time. At this time, it is necessary for the owner to humidify the room to avoid dry deformation of the floor. When decorating, be careful not to punch holes and nails on the ground to avoid leaking the geothermal pipeline, causing the geothermal system to run water and the floor to be scrapped. In addition, since the surface of the floor is a heat dissipating surface, as far as possible, no fixed decorative parts or furniture without legs should be placed on the floor, and it is not suitable to add a platform to avoid affecting the flow of hot air, resulting in poor heating effect in the room. Because the surface temperature of the floor is relatively high, it is better not to place the glassware and porcelain containing water directly on the ground in the winter. In order to avoid uneven heating, thermal expansion and contraction, the vessel is broken, and the water in the home is "Golden Mountain". . Geothermal flooring has become a fashion accessory in home decoration, but everyone must pay more attention to details when purchasing and paving, especially in terms of maintenance, the requirements for geothermal flooring are higher. Product Features
5. The pre-opened silica gel lid allows the Pipette tip or probe to enter the hole without damaging the lid.
6. After the third party inspection, no RNA/DNA enzyme contamination
Film Seals,Sealing Film For PCR Plates,Sealing Film QPCR,96 Well Plate Sealing Film,Silicone Sealing Mat Yong Yue Medical Technology(Kunshan) Co.,Ltd , https://www.yonyue.com
1. The product is easy to open and close, which can effectively seal deep well plates, sample tubes, etc., which is convenient for operation and saves time.
2. Good airtightness can prevent the volatilization of various solvents.
3. Tolerate a wide temperature range, suitable for various experiments.
4. Resistant to chemical corrosion and used for low-temperature storage.
7. It can be used on automated machines, and the product size conforms to the SBS standard
8. It can be used with stickers, silica gel, and sealed without leakage. 96 round-hole silica gel and 8-hole silica gel strip with matching sealing plate
9. Good flatness, can be transported long distance after sealing with heat sealing film
10. The products are produced and packaged in a 100,000-class dust-free workshop, and the product quality is stable
11. Alphabetical sorting and cut corner marking make the storage and collection of samples more convenient and faster.
12. Each package has an independent article number and batch number identification, which is convenient for quality tracking and traceability